Supra generations

    The Toyota Supra Community for all Supra generations

    Toyota Supra A90

    Owners of the fifth generation Toyota Supra are thrilled about that car

    Toyota Supra MKIV

    In July 1993, the fourth and so far last generation of the Supra came on the market. Internationally, this type is called " Supra MKIV ".

    Toyota Supra MKIII

    In early 1986, the third generation of the Supra was introduced. It is also the first that has not been marketed with the suffix Celica.

    Celica Supra (MK2)

    The second generation was presented in the fall of 1981 and had a completely independent drive with the new (170 hp) 6-cylinder engines.

    2000GT & Supra MK1

    The first Supra built from spring 1978 to summer 1981 was still offered as a top version of the Celica first in Japan and later in the United States.

    Toyota Classics

    Photos, videos and informations about the Toyota 2000GT & Celica XX Supra

    Toyota 2000GT & Celica Supra

    The first Supra built from spring 1978 to summer 1981 was still offered as a top version of the Celica first in Japan and later in the United States.

    MK 2

    Photos, Videos, Infos and more for the Toyota Supra MK2

    Celica Supra MKII (MA 60/61)

    The second generation was presented in the fall of 1981 and had a completely independent drive with the new (170 hp) 6-cylinder engines.

    MK 3

    Photos, Videos, Infos and more for the Toyota Supra MK3s

    Toyota Supra MKIII (MA70/MA71)

    The second generation was presented in the fall of 1981 and had a completely independent drive with the new (170 hp) 6-cylinder engines.

    MK 4

    Photos, Videos, Infos and more for the Toyota Supra MKIV

    Toyota Supra MKIV (A80)

    In July 1993, the fourth and so far last generation of the Supra came on the market. Internationally, this type is called " Supra MKIV ".

    MK 5

    Photos, videos, informations and more about the new Toyota Supra

    Toyota Supra MKV (A90)

    Owners of the fifth generation Toyota Supra are thrilled about that car
    Modelle: ClassicsMK2MK3MK4MK5
    Repair Manual

    Cylinder head reassembly - 2JZ-GTE Engine - Toyota Supra A80

    with love by
    Donate their awesome work
    
    • Thoroughly clean all parts to be assembled.
    • Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
    • Replace all gaskets and oil seals with new ones.
    1. Install heater union
      When using a new cylinder head, a new heater union must be installed.
      1. Apply adhesive to the end of the heater union as shown in the illustration.
        Adhesive:
        Part No. 08833-00070, THREE BOND 1324 or equivalent
      2. Using a wooden block and hammer, tap in a new heater union, leaving standard position protruding from the cylinder head.
        Standard protrusion:
        48 mm (1.89 in.)
    2. Install valves
      1. Install a new oil seal on the valve guide bushing.
      2. Install these parts:
        1. Valve
        2. Spring seat
        3. Valve spring
        4. Spring retainer
        Confirm the correct direction of the valve spring.
      3. Using SST, compress the valve spring and place the 2 keepers around the valve stem.
        SST 09202-70020 (09202-00010)
      4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
    3. Install valve lifters and shims
      1. Install the valve lifter and shim.
      2. Check that the valve lifter rotates smoothly by hand.
    4. Install EGR cooler
      Install a new gasket and the EGR cooler with the 8 bolts.
      Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
    5. Install camshaft position sensors
      Install the gasket and sensor with the 2 bolts.
      Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
    6. Install engine hangers and ground strap
      Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
    This guide is based on the book edition Toyota (RM502U, 1997)
    Oxwall Community Software